Posted on

The Easy Kit is a complete working set that even a total beginner can handle. This guide walks you through all seven steps – from preparation and spore inoculation, through incubation, to replanting into the tray and the growing phase. The same procedure also applies to a standalone Mushbag.

Summary at a glance

  • Always work with clean hands and a disinfected injection port.
  • Shake the spore syringe, heat the needle until it glows red and let it cool for 15–20 s.
  • Incubate the inoculated Mushbag in the dark at about 26 °C.
  • Replant the colonised substrate into the tray: perlite, substrate, vermiculite.
  • Once the vermiculite is colonised, remove the lid and put the tray into the filter bag (23–26 °C, light).

What the Easy Kit contains

  • Mushbag – sterile sorghum in a bag with an air micro-filter and injection port
  • spore syringe (3 ml)
  • growing tray with lid
  • vermiculite and perlite
  • alcohol swab

You will also need: a lighter, boiled water and a warm, dark place – ideally an opaque box, such as our black box.

We make the substrate for our Mushbags from sorghum – a gluten-free grain that is better suited for this purpose.

Step-by-step guide

1. Wash your hands

Always wash your hands thoroughly before you start working. Cleanliness is the most important protection against contamination – especially when replanting (step 6), when you touch the substrate.

2. Clean the injection site

Disinfect the injection site on the Mushbag with an alcohol-soaked swab. Do not touch the site afterwards.

3. Heat the needle with a jet-flame lighter

Shake the spore syringe well for 5–10 seconds so the spores spread evenly in the solution. Then heat the needle over the flame until it glows red (watch out for the plastic end of the needle) and let it cool for 15–20 seconds. A hot needle would damage the spores during injection.

4. Inoculate

Wipe the injection port once more with an alcohol swab. Carefully insert the needle into the Mushbag and squeeze out the contents of the syringe. Then gently rub the bag to spread the spores through the substrate.

5. Incubate

Store the Mushbag in a warm, dark place at about 26 °C – an opaque box is best. Lower temperatures slow down incubation. We do not recommend heat pads for warming; we recommend an aquarium heater and water.

Warning: Never place the Mushbag directly on the heater – the substrate would dry out. If the Mushbag becomes contaminated, it cannot be saved. We explain how to recognise contamination in the article Mushbag contamination.

6. Replant

Once the whole substrate is colonised by white mycelium, replant it into the prepared tray:

  1. make a layer of perlite at the bottom (the whole bag) and pour boiled, cooled water over it up to two thirds of the layer,
  2. put a layer of colonised substrate on the perlite,
  3. finish with a layer of vermiculite – pour boiling water over it, let it soak and cool down, and use it to cover the substrate.

Close the tray with the lid and place it in a warm (23–26 °C) and light place. Spare vermiculite and perlite can be found in accessories.

7. Growing phase

When the mycelium in the tray has grown through the vermiculite layer, remove the lid. Place the tray into the filter bag and put it back in a warm (23–26 °C) and light place (not in direct sunlight).

Approximate timeline

PhaseConditionsApproximate duration
Incubation in the Mushbagdark, about 26 °C2–4 weeks, until fully colonised
Vermiculite colonisation in the traylight, 23–26 °C, lid closedabout 1–2 weeks
Growing phaselight, 23–26 °C, filter bagdepends on strain

Times are approximate only – they depend on temperature, spore strain and how cleanly you work.

Most common mistakes

  • Needle not flamed or not cooled – risk of contamination, or of damaged spores.
  • Mushbag placed directly on the heater – overheated and dried-out substrate.
  • Temperature too low during incubation – colonisation takes much longer.
  • Opening the Mushbag “to check” – mould spores get into the sterile environment.

Frequently asked questions

How long does Mushbag incubation take?

Roughly 2–4 weeks at about 26 °C. Colonisation slows down at lower temperatures. The Mushbag is ready for replanting once the whole substrate is fully colonised by white mycelium.

What temperature does the Easy Kit need?

About 26 °C in the dark during incubation, then about 23–26 °C in a light place after replanting into the tray, but not in direct sunlight.

Why is the needle heated with a jet-flame lighter?

Heating the needle over the flame until it glows red sterilises it, so no bacteria or mould spores get into the Mushbag when you inject. Watch out for the plastic end of the needle. Let it cool for 15–20 seconds before injecting – a hot needle would damage the spores.

Can I put the Mushbag directly on a heater?

No, the substrate would dry out. We do not recommend heat pads for warming – we recommend an aquarium heater and water.

What water should I use after replanting?

Pour boiled, cooled water over the perlite (the whole bag) up to two thirds of its layer. Pour boiling water over the vermiculite, let it soak and cool down, and only then cover the substrate with it.

What is the Easy Kit intended for?

The set does not contain any psychoactive or banned substances. We sell it exclusively for research, ethnobotanical and collecting purposes.

Warning: This product does not contain any psychoactive or banned substances. It is sold exclusively for research, ethnobotanical and collecting purposes. By growing it you are in breach of the laws of the Czech Republic. Eating the fruiting bodies is not recommended. All texts are for information only and serve general descriptive and educational purposes.